xNightR00T File Manager

UDPLITE-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    mib-2, Unsigned32,
    Counter32, Counter64   FROM SNMPv2-SMI           -- [RFC2578]

    TimeStamp              FROM SNMPv2-TC            -- [RFC2579]

    MODULE-COMPLIANCE,
    OBJECT-GROUP           FROM SNMPv2-CONF          -- [RFC2580]

    InetAddress,
    InetAddressType,
    InetPortNumber         FROM INET-ADDRESS-MIB;    -- [RFC4001]

udpliteMIB MODULE-IDENTITY
    LAST-UPDATED "200712180000Z"       -- 18 December 2007
    ORGANIZATION "IETF TSV Working Group (TSVWG)"
    CONTACT-INFO
           "IETF TSV Working Group
            http://www.ietf.org/html.charters/tsvwg-charter.html
            Mailing List: tsvwg@ietf.org




            Gerrit Renker, Godred Fairhurst
            Electronics Research Group
            School of Engineering, University of Aberdeen
            Fraser Noble Building, Aberdeen AB24 3UE, UK"
    DESCRIPTION
           "The MIB module for managing UDP-Lite implementations.
            Copyright (C) The IETF Trust (2008).  This version of
            this MIB module is part of RFC 5097; see the RFC
            itself for full legal notices."

    REVISION "200712180000Z"           -- 18 December 2007
    DESCRIPTION
           "Initial SMIv2 revision, based on the format of the UDP
            MIB module (RFC 4113) and published as RFC 5097."
    ::= { mib-2 170 }

udplite      OBJECT IDENTIFIER ::= { udpliteMIB 1 }

udpliteInDatagrams OBJECT-TYPE         -- as in UDP-MIB
    SYNTAX     Counter64
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The total number of UDP-Lite datagrams that were
            delivered to UDP-Lite users.
            Discontinuities in the value of this counter can occur
            at re-initialisation of the management system, and at
            other times as indicated by the value of
            udpliteStatsDiscontinuityTime."
    ::= { udplite 1 }

udpliteInPartialCov OBJECT-TYPE        -- new in UDP-Lite
    SYNTAX     Counter64
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The total number of UDP-Lite datagrams that were
            delivered to UDP-Lite users (applications) and whose
            checksum coverage was strictly less than the datagram
            length.
            Discontinuities in the value of this counter can occur
            at re-initialisation of the management system, and at
            other times as indicated by the value of
            udpliteStatsDiscontinuityTime."
    ::= { udplite 2 }






udpliteNoPorts OBJECT-TYPE             -- as in UDP-MIB
    SYNTAX     Counter32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The total number of received UDP-Lite datagrams for
            which there was no listener at the destination port.
            Discontinuities in the value of this counter can occur
            at re-initialisation of the management system, and at
            other times as indicated by the value of
            udpliteStatsDiscontinuityTime."
    ::= { udplite 3 }

udpliteInErrors OBJECT-TYPE            -- as in UDP-MIB
    SYNTAX     Counter32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The number of received UDP-Lite datagrams that could not
            be delivered for reasons other than the lack of an
            application at the destination port.
            Discontinuities in the value of this counter can occur
            at re-initialisation of the management system, and at
            other times as indicated by the value of
            udpliteStatsDiscontinuityTime."
    ::= { udplite 4 }

udpliteInBadChecksum OBJECT-TYPE       -- new in UDP-Lite
    SYNTAX     Counter32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The number of received UDP-Lite datagrams whose checksum
            could not be validated.  This includes illegal checksum
            coverage values, as their use would lead to incorrect
            checksums.
            Discontinuities in the value of this counter can occur
            at re-initialisation of the management system, and at
            other times as indicated by the value of
            udpliteStatsDiscontinuityTime."
    REFERENCE "RFC 3828, section 3.1"
    ::= { udplite 5 }

udpliteOutDatagrams OBJECT-TYPE        -- as in UDP-MIB
    SYNTAX     Counter64
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION



           "The total number of UDP-Lite datagrams sent from this
            entity.
            Discontinuities in the value of this counter can occur
            at re-initialisation of the management system, and at
            other times as indicated by the value of
            udpliteStatsDiscontinuityTime."
    ::= { udplite 6 }

udpliteOutPartialCov OBJECT-TYPE       -- new in UDP-Lite
    SYNTAX     Counter64
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The total number of udpliteOutDatagrams whose
            checksum coverage was strictly less than the
            datagram length.
            Discontinuities in the value of this counter can occur
            at re-initialisation of the management system, and at
            other times as indicated by the value of
            udpliteStatsDiscontinuityTime."
    ::= { udplite 7 }

udpliteEndpointTable OBJECT-TYPE
    SYNTAX     SEQUENCE OF UdpLiteEndpointEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "A table containing information about this entity's
            UDP-Lite endpoints on which a local application is
            currently accepting or sending datagrams.

            The address type in this table represents the address
            type used for the communication, irrespective of the
            higher-layer abstraction.  For example, an application
            using IPv6 'sockets' to communicate via IPv4 between
            ::ffff:10.0.0.1 and ::ffff:10.0.0.2 would use
            InetAddressType ipv4(1).

            Like the udpTable in RFC 4113, this table also allows
            the representation of an application that completely
            specifies both local and remote addresses and ports.  A
            listening application is represented in three possible
            ways:

            1) An application that is willing to accept both IPv4
               and IPv6 datagrams is represented by a
               udpliteEndpointLocalAddressType of unknown(0) and a
               udpliteEndpointLocalAddress of ''h (a zero-length



               octet-string).

            2) An application that is willing to accept only IPv4
               or only IPv6 datagrams is represented by a
               udpliteEndpointLocalAddressType of the appropriate
               address type and a udpliteEndpointLocalAddress of
               '0.0.0.0' or '::' respectively.

            3) An application that is listening for datagrams only
               for a specific IP address but from any remote
               system is represented by a
               udpliteEndpointLocalAddressType of the appropriate
               address type, with udpliteEndpointLocalAddress
               specifying the local address.

            In all cases where the remote address is a wildcard,
            the udpliteEndpointRemoteAddressType is unknown(0),
            the udpliteEndpointRemoteAddress is ''h (a zero-length
            octet-string), and the udpliteEndpointRemotePort is 0.

            If the operating system is demultiplexing UDP-Lite
            packets by remote address/port, or if the application
            has 'connected' the socket specifying a default remote
            address/port, the udpliteEndpointRemote* values should
            be used to reflect this."
    ::= { udplite 8 }

udpliteEndpointEntry OBJECT-TYPE
    SYNTAX     UdpLiteEndpointEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "Information about a particular current UDP-Lite endpoint.
            Implementers need to pay attention to the sizes of
            udpliteEndpointLocalAddress/RemoteAddress, as Object
            Identifiers (OIDs) of column instances in this table must
            have no more than 128 sub-identifiers in order to remain
             accessible with SNMPv1, SNMPv2c, and SNMPv3."
    INDEX   { udpliteEndpointLocalAddressType,
              udpliteEndpointLocalAddress,
              udpliteEndpointLocalPort,
              udpliteEndpointRemoteAddressType,
              udpliteEndpointRemoteAddress,
              udpliteEndpointRemotePort,
              udpliteEndpointInstance }
    ::= { udpliteEndpointTable 1 }

UdpLiteEndpointEntry ::= SEQUENCE {



        udpliteEndpointLocalAddressType   InetAddressType,
        udpliteEndpointLocalAddress       InetAddress,
        udpliteEndpointLocalPort          InetPortNumber,
        udpliteEndpointRemoteAddressType  InetAddressType,
        udpliteEndpointRemoteAddress      InetAddress,
        udpliteEndpointRemotePort         InetPortNumber,
        udpliteEndpointInstance           Unsigned32,
        udpliteEndpointProcess            Unsigned32,
        udpliteEndpointMinCoverage        Unsigned32,
        udpliteEndpointViolCoverage       Counter32
}

udpliteEndpointLocalAddressType OBJECT-TYPE
    SYNTAX     InetAddressType
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "The address type of udpliteEndpointLocalAddress.  Only
            IPv4, IPv4z, IPv6, and IPv6z addresses are expected, or
            unknown(0) if datagrams for all local IP addresses are
            accepted."
    ::= { udpliteEndpointEntry 1 }

udpliteEndpointLocalAddress OBJECT-TYPE
    SYNTAX     InetAddress
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "The local IP address for this UDP-Lite endpoint.

            The value of this object can be represented in three
            possible ways, depending on the characteristics of the
            listening application:

            1. For an application that is willing to accept both
               IPv4 and IPv6 datagrams, the value of this object
               must be ''h (a zero-length octet-string), with
               the value of the corresponding instance of the
               EndpointLocalAddressType object being unknown(0).

            2. For an application that is willing to accept only
               IPv4 or only IPv6 datagrams, the value of this
               object must be '0.0.0.0' or '::', respectively,
               while the corresponding instance of the
               EndpointLocalAddressType object represents the
               appropriate address type.

            3. For an application that is listening for data



               destined only to a specific IP address, the value
               of this object is the specific IP address for
               which this node is receiving packets, with the
               corresponding instance of the
               EndpointLocalAddressType object representing the
               appropriate address type.

            As this object is used in the index for the
            udpliteEndpointTable, implementors should be careful
            not to create entries that would result in OIDs with
            more than 128 sub-identifiers; this is because of SNMP
            and SMI limitations."
    ::= { udpliteEndpointEntry 2 }

udpliteEndpointLocalPort OBJECT-TYPE
    SYNTAX     InetPortNumber
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "The local port number for this UDP-Lite endpoint."
    ::= { udpliteEndpointEntry 3 }

udpliteEndpointRemoteAddressType OBJECT-TYPE
    SYNTAX     InetAddressType
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "The address type of udpliteEndpointRemoteAddress.  Only
            IPv4, IPv4z, IPv6, and IPv6z addresses are expected, or
            unknown(0) if datagrams for all remote IP addresses are
            accepted.  Also, note that some combinations of
            udpliteEndpointLocalAdressType and
            udpliteEndpointRemoteAddressType are not supported.  In
            particular, if the value of this object is not
            unknown(0), it is expected to always refer to the
            same IP version as udpliteEndpointLocalAddressType."
    ::= { udpliteEndpointEntry 4 }

udpliteEndpointRemoteAddress OBJECT-TYPE
    SYNTAX     InetAddress
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "The remote IP address for this UDP-Lite endpoint.  If
            datagrams from any remote system are to be accepted,
            this value is ''h (a zero-length octet-string).
            Otherwise, it has the type described by
            udpliteEndpointRemoteAddressType and is the address of



            the remote system from which datagrams are to be
            accepted (or to which all datagrams will be sent).

            As this object is used in the index for the
            udpliteEndpointTable, implementors should be careful
            not to create entries that would result in OIDs with
            more than 128 sub-identifiers; this is because of SNMP
            and SMI limitations."
    ::= { udpliteEndpointEntry 5 }

udpliteEndpointRemotePort OBJECT-TYPE
    SYNTAX     InetPortNumber
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "The remote port number for this UDP-Lite endpoint.  If
            datagrams from any remote system are to be accepted,
            this value is zero."
    ::= { udpliteEndpointEntry 6 }

udpliteEndpointInstance OBJECT-TYPE
    SYNTAX     Unsigned32 (1..'ffffffff'h)
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
           "The instance of this tuple.  This object is used to
            distinguish among multiple processes 'connected' to
            the same UDP-Lite endpoint.  For example, on a system
            implementing the BSD sockets interface, this would be
            used to support the SO_REUSEADDR and SO_REUSEPORT
            socket options."
    ::= { udpliteEndpointEntry 7 }

udpliteEndpointProcess OBJECT-TYPE
    SYNTAX     Unsigned32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "A unique value corresponding to a piece of software
            running on this endpoint.

            If this endpoint is associated with more than one piece
            of software, the agent should choose one of these.  As
            long as the representative piece of software
            is running and still associated with the endpoint,
            subsequent reads will consistently return the same
            value.  The implementation may use any algorithm
            satisfying these constraints (e.g., choosing the entity



            with the oldest start time).

            This identifier is platform-specific.  Wherever possible,
            it should use the system's native, unique identification
            number as the value.

            If the SYSAPPL-MIB module is available, the value should
            be the same as sysApplElmtRunIndex.  If not available, an
            alternative should be used (e.g., the hrSWRunIndex of the
            HOST-RESOURCES-MIB module).

            If it is not possible to uniquely identify the pieces of
            software associated with this endpoint, then the value
            zero should be used.  (Note that zero is otherwise a
            valid value for sysApplElmtRunIndex.)"
    ::= { udpliteEndpointEntry 8 }

udpliteEndpointMinCoverage OBJECT-TYPE -- new in UDP-Lite
    SYNTAX     Unsigned32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The minimum checksum coverage expected by this endpoint.
            A value of 0 indicates that only fully covered datagrams
            are accepted."
    REFERENCE "RFC 3828, section 3.1"
    ::= { udpliteEndpointEntry 9 }

udpliteEndpointViolCoverage OBJECT-TYPE -- new / optional in UDP-Lite
    SYNTAX     Counter32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The number of datagrams received by this endpoint whose
            checksum coverage violated the minimum coverage threshold
            set for this connection (i.e., all valid datagrams whose
            checksum coverage was strictly smaller than the minimum,
            as defined in RFC 3828).
            Discontinuities in the value of this counter can occur
            at re-initialisation of the management system, and at
            other times as indicated by the value of
            udpliteStatsDiscontinuityTime."
    ::= { udpliteEndpointEntry 10 }








udpliteStatsDiscontinuityTime OBJECT-TYPE
    SYNTAX     TimeStamp
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
           "The value of sysUpTime at the most recent occasion at
            which one or more of the UDP-Lite counters suffered a
            discontinuity.
            A value of zero indicates no such discontinuity has
            occurred since the last re-initialisation of the local
            management subsystem."
    ::= { udplite 9 }

-- Conformance Information

udpliteMIBConformance OBJECT IDENTIFIER ::= { udpliteMIB 2 }

udpliteMIBCompliance MODULE-COMPLIANCE
       STATUS     current
       DESCRIPTION
           "The compliance statement for systems that implement
            UDP-Lite.

            There are a number of INDEX objects that cannot be
            represented in the form of OBJECT clauses in SMIv2,
            but for which we have the following compliance
            requirements, expressed in OBJECT clause form in this
            description clause:

            -- OBJECT      udpliteEndpointLocalAddressType
            -- SYNTAX      InetAddressType { unknown(0), ipv4(1),
            --                               ipv6(2), ipv4z(3),
            --                               ipv6z(4) }
            -- DESCRIPTION
            --     Support for dns(16) is not required.
            -- OBJECT      udpliteEndpointLocalAddress
            -- SYNTAX      InetAddress (SIZE(0|4|8|16|20))
            -- DESCRIPTION
            --     Support is only required for zero-length
            --     octet-strings, and for scoped and unscoped
            --     IPv4 and IPv6 addresses.
            -- OBJECT      udpliteEndpointRemoteAddressType
            -- SYNTAX      InetAddressType { unknown(0), ipv4(1),
            --                               ipv6(2), ipv4z(3),
            --                               ipv6z(4) }
            -- DESCRIPTION
            --     Support for dns(16) is not required.
            -- OBJECT      udpliteEndpointRemoteAddress



            -- SYNTAX      InetAddress (SIZE(0|4|8|16|20))
            -- DESCRIPTION
            --     Support is only required for zero-length
            --     octet-strings, and for scoped and unscoped
            --     IPv4 and IPv6 addresses.
           "
    MODULE  -- this module
         MANDATORY-GROUPS { udpliteBaseGroup,
                            udplitePartialCsumGroup,
                            udpliteEndpointGroup    }
     GROUP               udpliteAppGroup
     DESCRIPTION
            "This group is optional and provides supplementary
             information about the effectiveness of using minimum
             checksum coverage thresholds on endpoints."
    ::= { udpliteMIBConformance 1 }

udpliteMIBGroups OBJECT IDENTIFIER ::= { udpliteMIBConformance 2 }

udpliteBaseGroup OBJECT-GROUP          -- as in UDP
    OBJECTS   { udpliteInDatagrams, udpliteNoPorts, udpliteInErrors,
                udpliteOutDatagrams, udpliteStatsDiscontinuityTime }
    STATUS     current
    DESCRIPTION
           "The group of objects providing for counters of
            basic UDP-like statistics."
    ::= { udpliteMIBGroups 1 }

udplitePartialCsumGroup OBJECT-GROUP  -- specific to UDP-Lite
    OBJECTS   { udpliteInPartialCov,
                udpliteInBadChecksum,
                udpliteOutPartialCov  }
    STATUS     current
    DESCRIPTION
           "The group of objects providing for counters of
            transport layer statistics exclusive to UDP-Lite."
    ::= { udpliteMIBGroups 2 }

udpliteEndpointGroup OBJECT-GROUP
    OBJECTS    { udpliteEndpointProcess, udpliteEndpointMinCoverage }
    STATUS     current
    DESCRIPTION
           "The group of objects providing for the IP version
            independent management of UDP-Lite 'endpoints'."
    ::= { udpliteMIBGroups 3 }






udpliteAppGroup OBJECT-GROUP
    OBJECTS    { udpliteEndpointViolCoverage }
    STATUS     current
    DESCRIPTION
           "The group of objects that provide application-level
            information for the configuration management of
            UDP-Lite 'endpoints'."
    ::= { udpliteMIBGroups 4 }

END